
Industrial Slitter Combo
A solution for all of your onsite and factory needs for slitting your master coils or 48" wide panels of flat stock to the correct width.
Features & Benefits
1. Adjustable Knives
Position your knives in seconds with easy access adjustment screws.
2. Dual Cuts with Each Pass
Slitters come standard with 4 knives that allow 2 cuts on each pass (1 top and 1 bottom knife required for each cut)
3. Roller Exit Table
6’ roller table supports sheet run off onto any surface.
4. Includes 110V Motor

5. Booster Blocks

6. Adjustable Feed Tray Guides

7. UniStand™ EZ
Allows effortless movement and easy storage in an unused corner. Spins on a dime! Breaks down in minutes for easy storage.
8. Quick Assembly ⁄ Disassembly
Quick removal T-knobs and faspins allow the slitter to be set up and broken down for easy transport and storage in minutes.
"I have a 48 inch slitter combo and a 24 inch slitter. Excellent tools and equipment! "
-Chris P.
Grand Bank, NL


Slit
Each Trim-A-Slitter™ comes standard with 4 knives that allow two cuts with each pass. Additional knives may be added to increase productivity.*
Ribform
Adds rigidity to your metal with a slightly raised rib. Also helps to eliminate ripples and adds a decorative ‘shadow line’ to wider fascia and frieze board.*
Perforate
Perforator die set (optional) allows you to perforate up to .032" aluminum, copper coil, and 24, 26 and 29 gauge painted steel with ease. (HD motor upgrade required)** The slitting, rib forming, and perforating capacities are based on standard metal properties for coil & sheet. Please contact our factory for capacities on your specific material. 1-800-826-6275
DETAILS & SPECIFICATIONS
Forget the need to use your time consuming snips, shears, or nibblers to cut down your metals. The Industrial Trim-A-Slitter™ Combo quickly and easily slits your master coils or sheets to the desired width, leaving a clean, burr free factory edge. Slitting knives adjust in seconds. The Industrial Trim-A-Slitter™ Combo is nearly turnkey ready to set up onsite or in your metal shop and can be disassembled for easy transport and storage in minutes.
Slitter Configuration
![]() |
![]() |
![]() |
![]() |
1 slit | 2 simultaneous slits | *1 simultaneous slit & rib | |
![]() |
![]() |
![]() |
|
From the Factory | 1 rib (Facing up) | 1 rib (Facing down) | *2 ribs simultaneous (Facing up) |
*Additional knives required.
CORE SPECS
Model
Length
Arbor
Weight
SCI48
48" (121.9 cm) (of Slitter)
2"
265 lbs (120.5 kg)
SLITTING CAPACITIES*
Material
Maximum Thickness
Aluminum (3003H14)
.040" (1.0 mm) slitting and perforating
Galvanized Steel
24 ga. (0.6 mm)
Painted Steel (Grade D)
24 ga. (0.6 mm)
Roofing Copper
24 oz.
Zinc
.040" (1.0 mm)
Stainless Steel (304L)
Please call for capacities
View our Slitter Accessories page for specs on our optional equipment.
DOCUMENTS & VIDEOS
Documents
Videos
Most fasteners used in Van Mark tools are standard off-the-shelf nuts & bolts. This was intentional. We use standard fasteners to allow you to get back to work more quickly if something goes missing. Using standard replacement hardware like nuts, bolts & pull-pins will not affect your warranty. For more information, please contact Van Mark directly.
For Sales Literature on our Brakes and Accessories, see our Media Package page
WARRANTY
1 Year Manufacturer's Limited Warranty
Van Mark Products Corporation warrants this product against defects in material or workmanship for or a period of 1-year from the date of original purchase. For details, click here.